Get the MiniTool Programs for a try now. And you need to wait for a few minutes, so be patient. You should make sure either the original hard drive or the target disk is disconnected to your computer. Or else, the Windows operating system may mark one disk as offline.
Just get the Trial Edition of this ghost clone software to have a try. MiniTool Solution Ltd. By means of this all-in-one partition manager, you can manage your disk or partition well.
The former is used to clone the system disk as well as a data disk. And the latter can help to clone the entire system disk or only migrate OS drives to another disk. Here we take the former as an example.
How to ghost a hard drive with the best ghost software? If you need to deal with the system disk, the Free Edition doesn't support and you need to use the Professional or above edition.
Then click Copy Disk in the left action panel after selecting the target hard drive. Step 4: Then some information about how to boot from the target disk will be shown here.
Just do it in the event of system corruption. In this post, we tell you two backup strategies — image and clone. In addition, you can also adopt another piece of ghost drive software — MiniTool Partition Wizard to clone your disk for backup.
Suppose that you have some questions whiling using our our computer ghosting software, remember to tell us by leaving one comment in the following zone or writing an email to our support team via [email protected]. Also, the suggestions are appreciated here. Download Partition Wizard. Summary : How to ghost a hard drive for data protection? Read More. How to do it? The laptop only supports one hard disk. So, please connect your target disk to the laptop via a USB cable.
Then, do as the above guidance shows you. After hard drive cloning, remove the target disk. Be prepared to adjust any steps you take based on the specifics of your equipment. You can generally only ghost computers which use the same basic operating system and software. In addition, you cannot usually ghost a Mac onto a PC or vice versa.
Make sure your equipment is compatible before you begin. This article was written by a professional writer, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. To submit your questions or ideas, or to simply learn more, see our about us page: link below.
Home Hardware. Items you will need Two hard drives Ghosting software. Tips Ghosting software can vary in its particulars, both according to the software itself and according to the kind of computer and operating system you are using. Wait for five seconds the download will begin immediately after. Install Clonezilla onto your flash drive.
Click the "Choose a USB key" drop-down box at the top of the window, then click your flash drive's name. Check the "Format the key in FAT32" box near the bottom of the window. Click the lightning bolt icon at the bottom of the window. Leave both your USB flash drive and your external hard drive plugged in. Once you're done installing Clonezilla, you can proceed with ghosting your computer's hard drive.
Part 2. Format your external hard drive for your Mac. Formatting your external drive will ensure that it is compatible with both your Mac and other Macs. Download and install the "SuperDuper! Click the small, blue download link under the "Download Now" heading in the upper-right side of the page. Double-click the downloaded DMG file. Verify the software if prompted.
Click and drag the SuperDuper! Follow any on-screen prompts. Make sure your external hard drive is plugged into your Mac. Once you've finished formatting your external hard drive and installing SuperDuper!
Part 3. Restart your computer into the BIOS. In most cases, the key that you press to access the BIOS will be either one of the "function" keys e. You can check your specific computer model's manual or online documentation to find the BIOS key to use. If your computer's "function" keys are inverted, you'll need to hold down Fn while pressing the BIOS function key.
Set your computer to boot from your flash drive. Each computer's BIOS will vary slightly, so check your computer model's documentation for specific instructions on setting BIOS boot order; however, in most cases, you'll do something like this: Select the Boot or Advanced tab at the top of the screen.
Find the "Boot Order" section. Find your USB flash drive's name, then select it using the arrow keys. If this doesn't work, check the key legend on the right side or bottom of the screen for explicit key instructions.
Save your changes and exit the BIOS. You'll usually do this by pressing a key that's listed in the legend on either the right side of the screen or the bottom of the screen. Accept the default settings. Select a language. Select don't touch keymap. Select Start Clonezilla.
It's the top option on the following menu. Select device - device. This option is in the middle of the menu. Select Beginner. Doing so ensures that Clonezilla will take care of the more complicated settings.
Select disk to local disk. This is the top option on this page. Select the hard drive you want to clone. In most cases, you'll move the cursor to highlight the top hard drive; this is usually the sda hard drive the "a" refers to the first hard drive.
You can double-check that you're selecting the correct drive by looking at how many gigabytes of free space the drive has listed next to its name. A hard drive labelled "sdb" would be the second hard drive, "sdc" would refer to the third, and so on. Select your external hard drive. This will usually be the only option on the page, but check the hard drive's storage number e.
Select -pa poweroff. This ensures that Clonezilla will turn off your computer when it finishes cloning your hard drive, allowing you to remove your flash drive before restarting your computer.
If you don't remove your flash drive before restarting your computer, your computer will just reboot from the Clonezilla installation again.
0コメント